LED Driver LDR8-40
Tokistar’s LDR8-40 is a 40 Watt UL Recognized Class 2 LED Driver used to convert an AC input into an 8 VDC output. It may be operated from a wide range of input voltages. The enclosure is suitable for wet locations.
Part #: LDR8-40
Specifications
Input Range: 100-240 VAC
Frequency Range: 50/60 Hz
Output: 8 VDC (Adjustable +10% / -25%)
Max. Output Current: 5.0A
Max. Output Power: 40W
Protection: Overload, Overcurrent, Short Circuit
Operating Temperature: -30ºC to +60ºC
Mechanical Specifications
Dimensions: 3” x 9.75” x 2”
Weight: 1.94 lbs
Enclosure Rating: Nema 3/IP65
Mounting: Flange Mount
Connection: Knockouts for 1/2” Conduit
Compliance/Safety
Standards: UL Recognized Class 2/EN60950
LED Capacity
0.2 Watt LEDs: 200 pieces
LED Driver LDR8-80
Tokistar’s LDR8-80 is a dual output Class 2 LED Driver with two independent 40 Watt outputs. It may be operated from a wide range of input voltages. The enclosure is suitable for wet locations.
Part #: LDR8-80
Specifications
Input Range: 100~240 VAC
Frequency Range: 50/60 Hz
Output: 8 VDC (Adjustable +5% / -30%)
Max. Output Current: 10.0A (2 @ 5.0A)
Max. Output Power: 80W (2 @ 40W)
Protection: Overload, Overcurrent, Short Circuit
Operating Temperature: -30ºC to +60ºC
Mechanical Specifications
Dimensions: 3.6” x 11” x 2.25”
Weight: 4 lbs
Enclosure Rating: Nema 3/IP65
Mounting: Flange Mount
Connection: Knockouts for 1/2” Conduit
Compliance/Safety
Standards: UL Recognized Class 2/EN60950
LED Capacity
0.2 Watt LEDs: 400 pieces
Class 2 Transformers
In some areas, local codes may require our products be operated from Class 2 transformers only. Primary input is 120 VAC/60 Hz. Secondary circuits are limited to 5 Amps (60 Watts) at 12 Volts.
C2-60/12
The C2-60/12 transformer is a 60 Watt Class 2
transformer with a single 12 Volt output.
Multi-Output Class 2 Transformers
Larger capacity Class 2 transformers are available with multiple secondary outputs.
Each output is limited to 60 Watts @ 12 Volts. Primary input is 120 VAC/60 Hz.
T-12 Series Transformers
Tokistar's T-12 Series Transformers come in a wide range of sizes from 100 to 1,000 Watts. These transformers are enclosed within a Rainproof Type 3R Enclosure. Primary input is 120 VAC/60 Hz.
This proprietary Dimming System provides full-range dimming of Cable Lighting LEDs. The system components connect with CAT5 cable. Up to 25 dimmer packs may be connected in series if the total length of all CAT5 cable does not exceed 165 feet from the wall dimmer to the last dimmer pack. CAT5 cables are included with units.
Wall Dimmer (Part #: LC-DMR)
The remote wall dimmer has a rotary dial and on/off switch. Power to the wall dimmer is provided from the LED Driver powering the first Dimmer Pack.
Dimmer Pack (Part #: LC-1CH-DP)
Each dimmer pack receives an 8 VDC input from an LDR8-40 LED Driver and sends a 0-8 VDC output to the fixture. Logic input and output is communicated through CAT5 Cable.
Dimensions: 1-1/2” x 3-1/2” x 4-1/16”
Tokistar's LC-1CH-MULTI Dimmer Pack is compatible with industry-standard dimmers working on DMX or 0/1-10 VDC protocol. In the manual mode, a preset light level can be set without the use of any external dimmer.
Part #: LC-1CH-MULTI
Technical Specifications:
Max. Load: 40 Watts @ 8 VDC
Environmental Rating: Dry Location/IP20
Dimensions: 3/4” x 1-3/4” x 3-1/2”
Weight: 50g / 0.11 lbs
Listing: ETL Listed/CE Certified
Operating Temperature: 0~+50ºC
DMX Mode
In this mode, dimmer packs are addressable and may be used with any controller working on DMX protocol. Up to 36 dimmer packs may be connected in series. For applications exceeding 36 dimmer packs, an additional feed from the DMX dimmer is required. The additional feed(s) can be sent directly from the dimmer, or you may specify DMX Splitters. Consult factory on details of DMX Splitters.
Analog Mode 0/1-10VDC
For operation from devices using 0/1-10VDC protocol, up to 10 dimmer packs may be connected in series. For applications exceeding 10 dimmer packs, an additional feed from the analog dimming device is required.
Manual Mode
You may select a light intensity at which the fixtures operate. In this case, no external dimming device is required.
End Caps
Decorative end caps are available as an option. If individual fixtures are positioned end to end, long runs of product may require only two. Framed applications (such as rectangular layouts) may require no end caps at all.
Diffusion Filter
An optional diffusion filter is offered to soften the lighting effect.
Adhesive Tape
High-bond adhesive tape may be used to secure the fixtures in place.
